How to Connect I2C LCD Display to Arduino


In this tutorial, you will see how to connect i2c LCD display (Liquid Crystal Display) to Arduino using the i2c module. Before starting this article we will see what is i2c. I2C (I-square-C i.e IIC) means inter-integrated communication protocol. This is usually used to communicate between one master and multiple slaves. One of the best things about using I2C is we can reduce the connections (wiring). If you use normal LCD display, you need a total number of connections are 12. If you use I2C LCD display, you need only just 4 connection. By seeing the above example you may know the advantage of I2C protocol. I2C protocol is also known as 2 line protocol.

Components Required

Arduino Uno  [ Amazon India / GearBest ]

I2C LCD Display/IIC LCD Display   [ Amazon India / GearBest ]

Jumper Wires  [ Amazon India / GearBest ]

Pin Configuration of I2C LCD Display

iic lcd display

If you properly have seen the picture above, you will see a black adapter. That black adapter uses the PCF8574T IC chip which converts I2C serial data to parallel data for the LCD display. The blue color component you have seen in the above picture is a potentiometer which is used to adjust the brightness of the display.


I2C LCD Display

Arduino Uno    <->   LCD Display

5V     <—————>    Vcc

GND   <—————>    GND

A4     <—————>    SDA

A5     <—————>    SCL

Source Code

/* */
/*Import following Libraries*/
#include <Wire.h> 
#include <LiquidCrystal_I2C.h>
//I2C pins declaration
LiquidCrystal_I2C lcd(0x27, 16, 2);

void setup() 

lcd.begin();//Initializing display
lcd.backlight();//To Power ON the back light
//lcd.backlight();// To Power OFF the back light


void loop() 
//Write your code
lcd.setCursor(0,0); //Defining positon to write from first row,first column .
lcd.print(" Tech Maker "); //You can write 16 Characters per line .
delay(1000);//Delay used to give a dynamic effect
lcd.setCursor(0,1);  //Defining positon to write from second row,first column .
lcd.print("Like | Share");

lcd.clear();//Clean the screen
lcd.print(" SUBSCRIBE ");
lcd.print(" TECH MAKER ");

Custom Characters

#include <Wire.h>
#include <LiquidCrystal_I2C.h>

uint8_t bell[8]  = {0x4, 0xe, 0xe, 0xe, 0x1f, 0x0, 0x4};
uint8_t note[8]  = {0x2, 0x3, 0x2, 0xe, 0x1e, 0xc, 0x0};
uint8_t clock[8] = {0x0, 0xe, 0x15, 0x17, 0x11, 0xe, 0x0};
uint8_t heart[8] = {0x0, 0xa, 0x1f, 0x1f, 0xe, 0x4, 0x0};
uint8_t duck[8]  = {0x0, 0xc, 0x1d, 0xf, 0xf, 0x6, 0x0};
uint8_t check[8] = {0x0, 0x1 ,0x3, 0x16, 0x1c, 0x8, 0x0};
uint8_t cross[8] = {0x0, 0x1b, 0xe, 0x4, 0xe, 0x1b, 0x0};
uint8_t retarrow[8] = {	0x1, 0x1, 0x5, 0x9, 0x1f, 0x8, 0x4};

// Set the LCD address to 0x27 for a 16 chars and 2 line display
LiquidCrystal_I2C lcd(0x27, 16, 2);

void setup()

  lcd.createChar(0, bell);
  lcd.createChar(1, note);
  lcd.createChar(2, clock);
  lcd.createChar(3, heart);
  lcd.createChar(4, duck);
  lcd.createChar(5, check);
  lcd.createChar(6, cross);
  lcd.createChar(7, retarrow);

  lcd.print("Hello world...");
  lcd.setCursor(0, 1);
  lcd.print(" i ");
  lcd.print(" arduinos!");

// display all keycodes
void displayKeyCodes(void) {
  uint8_t i = 0;

  while (1) {
    lcd.print("Codes 0x");
    lcd.print(i, HEX);
    lcd.print(i + 16, HEX);
    lcd.setCursor(0, 1);

    for (int j = 0; j < 16; j++) {
      lcd.write(i + j);
    i += 16;


void loop()
  // Do nothing here...

Display Text sent over Serial Port in LCD Display

#include <Wire.h> 
#include <LiquidCrystal_I2C.h>

// Set the LCD address to 0x27 for a 16 chars and 2 line display
LiquidCrystal_I2C lcd(0x27, 16, 2);

void setup()
  // Initialize the serial port at a speed of 9600 baud

void loop()
  // If characters arrived over the serial port...
  if (Serial.available()) {
    // Wait a bit for the entire message to arrive
    // Clear the screen

    // Write all characters received with the serial port to the LCD.
    while (Serial.available() > 0) {


Download I2C LCD Arduino Code and Library


  1. Download and Install the Library attached.
  2. Download the code.
  3. Connect the components as the circuit attached.
  4. Edit the code as need to change the text on LCD.
  5. Upload the downloaded code.
  6. Now you can see the text on LCD.

Watch Video

Working of LCD Display

The LCD display has an inbuilt register, to store the data and commands given to the LCD display. It has two modes, one is READ mode and another is WRITE mode. In write mode commands to control the display is written to the register like display clear, shift right, the cursor on, etc., In WRITE mode the register is also written with data which is needed to be displayed on the display. Here a question arises how to differentiate between commands and data written to the register. There a pin called Register select (RS), if that pin is made to zero, then it is command register. If it is one, then it is a data register.

The selection of READ / WRITE is done by a pin R/W. If R/W is equal to zero, then it is write mode. If R/W is equal to one it is read mode.

lcd pinout

click on the link for more projects and tutorial on Arduino.

If you have any queries, feel free to comment below. I will reply as soon as possible.


19 thoughts on “How to Connect I2C LCD Display to Arduino”

  1. my code id shows no error and is getting compiled but i cannot see any temp or humidity display on the lcd. i have added the lcd library…do i have to add dht11 related library too?? please reply soon and help me fix the problem

  2. Hello! I would be grateful for help: I copied the libraries and with wire.h everything is fine, but Arduino cant’t find LiquidCrystal_I2C.h library. I copied the complete library with _V1.2.1 and also separetly, but it the problem is not fixed. Could you please tell, how I can fix it. Thanks! (Error message: No such file or directory)

  3. I’m getting the error message

    Arduino: 1.8.8 (Mac OS X), Board: “Arduino/Genuino Uno”

    /var/folders/zh/cspl3ptx5p33k6b2qn8ly6w80000gp/T/arduino_modified_sketch_73471/sketch_feb08a.ino: In function ‘void setup()’:
    sketch_feb08a:8:11: error: no matching function for call to ‘LiquidCrystal_I2C::begin()’
    lcd.begin();//Initializing display
    /Users/eric/Documents/Arduino/libraries/LiquidCrystal_I2C-1.1.2/LiquidCrystal_I2C.h:58:8: note: candidate expects 3 arguments, 0 provided
    exit status 1
    no matching function for call to ‘LiquidCrystal_I2C::begin()’

  4. I down loaded the Arduino IDE to my computer

    Where Do I load the code you provided ??
    Does all of the code go in a sketch or do I create separate sketchs?
    for lack of any direction

    I copied all of the code you have provided into a sketch when I click on the Verify button

    I’m getting the following message:

    “LiquidCrystal_I2C.h: No such file or directory”
    What directory are they talking about?
    Where does one go to get this directory
    If you down load it where do you down load it to?
    Does all these down loads get stored in the Adruino UNO?
    If stored on my computer do I have to have the UNO connected to the computer
    to run the serial display code I down loaded.



Leave a Reply